Description:-


In many cases we’ve seen, users want to change their console system and want to install EPS console on another system.


This Article will help you, to re-install EPS console on another system with couple of scenarios i.e


->  Current EPS console is already in running state.


-> Current EPS console is removed due to system got crashed & user had built a new system with new Operating System.


Let’s take above scenario one-by-one and steps to overcome it.


1. Current EPS console is already in running state.


 Current EPS console is already in running state, & if you are looking forward to migrating EPS console on another system or want to change console system, kindly follow below steps.


Step 1.


Open EPS console page first on your EPS console system.


 

Step 2.


Verify system where you want to install EPS console, is it EPS client system or new build system for EPS console.

If it’s EPS client system, remove the client from it. Through remote uninstall option from the console.




In this scenario, we are looking forward to declaring “192.168.1.24” as EPS console, so we’ll going to remove EPS client from it, through remote uninstall option for installing EPS console on it.


Step 3.


After uninstalling EPS client, reboot system & run EPS console setup on it, for installing EPS console.


Step 4.


Select the installation folder where you want to install EPS console.


Step 5.


Pre-Install Scan will be checked if any pre-requisite component is missing need to be installed.




Step 6.


Sever Information need to provide while installation of EPS console.




Step 7.


If your networked is configured with any proxy, then you need to fill proxy details over here.


 

 

Step 8.


Client Installation Settings, specify installation path for installing EPS client which can be changed as per your need. But we suggest you keep default one.

 

Step 9.


Set EPS console password and EPS client password.

 

Step 10.


Installation of EPS console.

 


Step 11.


Activate your EPS console with product key which can found under EPS license information from EPS console.

 



Step 12.


Access new EPS console.

 


Steps 13.


After accessing new console page , go to the old console page click on Clients tab & take back of Group & Policy before re-directing EPS client.

 


Note: -  After taking backup of Groups & Policy, now you need to import Groups & Policy to your New EPS console.


Step 14.


Now Open your old EPS console and go to Admin Setting -> Redirection option.

We’ll re-direct client from Old EPS to New EPS.



Step 15.


Now Open New EPS console and verify, EPS client should get redirected to the new console.



Points to Remember:-

- Kindly take Backup of Groups and Policy & Client list from Old EPS console.
- Import above backup to your New EPS console for Groups & Policy.
- After completing re-direction, once you see all your existing clients to New EPS console. Kindly remove Old EPS console from system.
- After removing Old EPS console, install EPS client in the old console by creating new client package from New EPS console.
- All you did with the migration of EPS console from one system to another.


2) Current EPS console got removed due to system got crashed & user had built a new system by installing New Operating System.


This scenario arises when your EPS console server got crashed & unable to boot or you had re-build server by re-installing Operating System.
Things you need to remember before re-installing EPS console.
- EPS setup file for eg. If your earlier EPS version was 7.2 then you need EPS 7.2 setup file only to proceed with the installation.
- For eg. If you're using older version Seqrite EPS 6.4 and Server got formatted or re-build & if you are looking forward to upgrading EPS console to available latest version 7.2 then you need to make little bit changes while installing EPS console.
- On any SEPS client system, verify below file.
  Go to C:\Program Files\Seqrite\Cagent\config\accaconf.ini and kindly note Serverport no. It’s 5052. This port number is will differ as per EPS    c c    console version.
  This port number need to enter during Client Installation Setting during SEPS console installation




- Server host name & IP address should be same as earlier or mentioned above accaconf.ini file for smooth communication with the client system.


Follow below step one by one for re-installing EPS console.


Step 1.


Execute EPS Setup file.




Step 2.


Select the installation folder where you want to install EPS console.


 

Step 3.


Pre-Install Scan will be checked if any pre-requisite component is missing need to be installed. You need to install IIS & pre-requisite component for EPS console.




Step 4.


Server Information needs to provide while installation of EPS console. In this Section, you need to select Server Information on which you previous EPS console was running and same information needs to select over here also.




Note:- Keep rest of the setting and port numbers as it is, do not change anything.


Step 5.


If your networked is configured with any proxy, then you need to fill proxy details over here.




Step 6.


Client Installation Settings, specify installation path for installing EPS client which can be changed as per your need. But we suggest you keep default one.





Note:- If you are installing Same Version of EPS client, then you don’t need to change ClientAgent Communication Port. But if your old console was older version i.e Seqrite 6.4 and now you're installing latest version Seqrite 7.2 than you need to change the port as per the below file on existing client system.
“C:\Program Files\Seqrite\Cagent\config\accaconf.ini”



Step 7.


Set EPS console password and EPS client password.





Step 8.


Installation of EPS console.




Step 9.


Activate your EPS console with product key which can found under EPS license information from EPS console.



Step 10.


Open EPS console page.

 Note: - You will found only one client under EPS console, to connect all EPS client with a console you need to restart Client Agent service from the client system or need to reboot client system for immediate reflection of a client under the console.
 You all set now to access EPS console page.


 Points to remember after re-installing EPS console.
- After re-installing EPS console, you won’t able to see EPS client under console or client status.
- You need to restart Client Agent service or need to reboot client machine for immediate reflection under the console. Once you have done Client will be    visible under the console.
- Import your backed up data like Groups & Policy. If it’s not backed up then you need to create new Groups & Policy as per your requirement.

Note: In the case of any query or require assistance, you may raise a ticket on below link to our Technical Support Team can assist you to resolve your query.
http://esupport.seqrite.com/support/tickets/new